Tag Archives: Repair

Tire Repair – Do it Yourself

Tire repair, nowadays, does not need to be done by the motorists themselves. There are a lot of tire repair shops in every locale you would be driving to; besides, there is always that good old spare tire available in the trunk of the car or in the undercarriage of the truck you’re driving. But come to think of it, there are times that you may pass through a remote area that does not have any repair establishments nor any residents to help during a flat tire occurrence. Worse is, the car or truck you’re driving does not have a spare tire, and you have to get out of that spot as soon as possible for any reason at all.

Well, simple tire problems like a nail hole in the tire tread can be repaired by the motorists themselves if they are in the above situation. They only need to have a pair of pliers to remove the nail that punched the tire tread, a jack to lift the vehicle up, a wrench to remove the tire, a small tire pump, and a tire repair kit  (you may purchase a repair kit from any of your neighborhood hardware or automotive part stores). Tire repair kits may vary in packing. The typical ones have a rasp tool, an inserting tool, and a few strands of plug strips/repair strings (others have a tube of rubber cement – an adhesive for the plug strips). 

The first thing to do is to park the car in a flat surface on the road shoulder, then make sure that the engine is shut off and parking brakes are engaged before lifting up the side where the flat tire is with a jack. If you can find anything handy to block any of the wheels other than the flat one to make sure that the car won’t move especially when it is already jacked up, better do it. Be safe. You are not doing this kind of thing every day, so you have to move with caution. Remove the flat tire by loosening the lug nuts with the tire wrench and try to remove the nail from it using your pliers. Get the rasp tool in the tire repair kit and scrape the nail hole to widen and remove some obstructions. Squirt some rubber cement into the hole before inserting a repair string/plug strip with the insert tool. Insert the strip all the way to the hole and pull out the insert tool. There might be a residual string protruding from the surface e of the tire tread that must be cut by a sharp blade. The plug strip must be flushed with the tire tread surface. This will prevent possible removal of the strip when driving. After this repair the tire is now ready for inflation with your handy motorized pump of even a foot operated inflator. Finally, you may now install the tire, lower your car, remove the jack and the wheel blocks, then leave the area with good tires and a smooth drive.

It is an advantage to have a tubeless tire repair kit and a handy tire pump with your jack and tire wrench whenever you drive out especially in remote places. Be prepared for this kind of situations. Tire repair – you can do it yourself.

Jonathan C. Tumalban manages a bus fleet maintenance shop for a tours and travel company in Saipan, CNMI. He spends a lot of free time in enhancing his other skills such as writing and web site design. He believes that writing, as well as a lot of reading, is not only an excellent past time but also a strong mental excercise. Jonathan writes about anything within the grasp of his understanding; with the intent to share these ideas, and to learn more whenever readers give comments and offer rectifications to any errors they may find in the articles.

Do it Yourself Hardwood Floor Repair

If you have a natural wood floor that has become damaged over the years, you do not have to keep it covered up with rugs or carpets, all you have to do is engage in some simple hardwood floor repair. It really only takes a few moments to replace the damaged planks and have your floor looking brand new again. In order to undergo this project you will need the following tools: a circular saw, hammer, chisel, construction adhesive, mallet, flooring nails, scrap wood, and wood filler.

Remove Damaged Planks

The first thing you need to do when repairing hardwood floors is to remove the planks in your floor that have been damaged. In order to remove a plank you must first carve a hole in the middle with your circular saw. Next, simply hammer out this center part with a chisel. Now it should be easy for you to pry out the remainder of the plank. Repeat this process for each of the remaining damaged planks. Also make sure that you remove any nails that remain in the floor. If they are too difficult to remove, you can always just drive them completely into the subfloor.

Replace

The next step of hardwood floor repair is to cut a new plank to replace the one you have removed. Your new plank should be slightly smaller than the one you removed, roughly 1/16 of an inch. This is important to do because the wood will naturally expand a little as time goes by. Next, you will want to place some adhesive on the backside of your new plank. This will help to keep it stationary after it has been installed. Next, you will place the plank into the floor, starting with the tongue side. You may find that you will have to tap it into place with a mallet. If so, make sure you place some old wood over top of your new plank in order to keep it protected.

Secure and Hide

The next thing you need to do when repairing hardwood floors is to use your flooring nails to secure the new plank to floor. You may also want to use your nail set to keep the nails hidden; it also won’t hurt to use wood filler to keep the screws out of sight. Now, the final step is to apply finish to the new plank, trying to match the tone of the other original planks as best as possible. It is often difficult to do this, so you may have to decide whether you should simply refinish the rest of the floor or have a plank or two of a slightly different shade.

As you can see, hardwood floor repair is not as difficult as you may have once thought. All it takes is a little effort and you can have your old floor looking as good as new.

Pieter West travels the world on a regular basis and have written about numerous subjects. He has an extensive knowledge about, finances, DIY, parenting advice and many more subjects.

Do It Yourself Air Conditioner Repair

Before you call a heating and cooling technician to take a look at your unit, there are a few simple repairs you can try yourself. This is especially handy if your a/c conks out on a Sunday morning. These simple repairs are also a good part of your annual maintenance plan. With regular cleaning, dust, dirt, and debris can clog your cooling fins, your coolant level can become low, and your blower may get dusty and dirty. While you can handle most of these maintenance and repair tasks in about an hour, only a professional Phenix City, AL heating and cooling professional can check your coolant levels.

The first piece of your cooling unit you want to check is the condenser. Begin by turning off the power, either on the unit itself or the main power switch for your home. Locate the condenser fins, which are small metal blades located around the unit. These fins accumulate dust, dirt, leaves, grass and pollen, which blocks the air flow into your home. If the airflow is blocked, your unit has to work harder to cool the home, using more power, which costs you more money.  Vacuum the fins with your household vacuum cleaner. You may want to use an attachment to reach some of the fins. You can then remove any remain debris with a soft brush. If you have are bent, you can gently straighten them back into shape with a butter knife.

Once the outside of you condenser is clean, unscrew the fan to gain access to the inside of the unit. Vacuum the inside of the unit, if you can reach. You may find that mice and other small animals like to winter in there, so be prepared for any animal debris. Use a hose to rinse of the fins and then check the motor to make sure it is properly lubricated. Add five drops of electric motor oil and then replace the fan.

Head inside your home and replace your dirty air filter and remove any particles and debris in the grill of this unit. You can use a vacuum or a soft cloth or brush to scrap away caked on dirt and dust.  Now you are ready to see if your maintenance and repairs worked.

Turn the power back on, and set the thermostat to cool, and select a lower than normal temperature. After about fifteen minutes, check the insulated tube- it should be cool. If it’s cool, you’ve fixed your problem and increased the energy efficiency of your unit. If you need a professional to take a look, there a number of HVAC specialists in and around Phenix AL. You will pay for both parts and labor if you need some professional help.

If you prefer to have a professional come out and complete a full diagnostic of your heating and air unit, be sure to make you appointment right around spring break or the beginning of the summer. Heating and air units in Phenix City, AL get a lot of use once the first heat wave heats, so make sure yours is running well before the temperature starts to rise.

If you are looking for information on heating and air phenix city al, click on the link. Or you can visit the website at http://dnahvac.com/heating-and-air-phenix-city!

Do It Yourself Air Conditioning Repair

Air conditioning repair can cost a lot if you don’t find yourself a reasonable contractor. And sometimes, they can even disrupt you from earning money because technicians often do house calls on your work hour. In spite of this though, homeowners should not forego the opportunity to acquire maintenance services, especially this summer. After all, they wouldn’t want their system to crash in the middle of the day because of some unchecked mechanical problem. Moreover, inspection could also help you minimize the risk of AC fires as well as excessive electrical consumption. Now, if you are eager to make sure your air conditioners are working properly but are not too eager to spend, here are some tips on how you can correct certain AC glitches on your own.

 

When the air conditioner is not taking out as much warm air as it should or if there is a foul odor released from your unit, you might be having some filter issues. If such is the case, then there’s no need to consult a specialist. You can just open the AC unit yourself from the inside of your house and change or clean the filter so it does not block air circulation. It’s expected for the filter to accumulate dust after prolonged use. So it would be best to check on the filter every month to avoid freezing up the condenser fins.

 

If the air conditioner’s performance does not improve, might as well proceed with clearing up the condenser from debris since any residue could potentially promote clogging and keep the AC from doing its job. You should also check your refrigerant containers since its depletion can also cause a decline in function. Afterwards, you ought to investigate the condition of the outside fan considering that it is responsible for getting rid of warm air. If there are leaves or dirt blocking it, the unit may not be able to cool down the room as well as it should.

 

If you notice that the air conditioner does not respond efficiently to temperature changes, check out the thermostat if it is still functioning. Because it’s highly likely that the AC is still working but the temperature gauge isn’t. What you could do to correct this setback is to, again, clean the sensor with a soft, clean brush, and then align it with the evaporator coil.

 

Now, if you perceive that your air conditioner is leaking, it is possible that the coils have some blockage or holes. To preclude overworking your unit and condoning further water damage and the growth of molds, you should open up your unit and check through the tubes. You could blow through it to get dirt out or check for air pockets. And if there is actual damage, you could replace the tube with another to preserve optimum function.

 

As you can see, air conditioning repair is something you can do on your own. If you are not as confident, there are more elaborate tutorial write ups and videos you can refer to for better results. However, if you have done all of the above and still are not able to improve your AC’s status, might as well call in specialists to solve the problem.

 

For more information about ac new orleans and new orleans heating visit our website http://gowlandsac.com/

Brake Repair Diy

Acquainting yourself with the basics of your vehicle’s brake repair instructions can help you alleviate a bit of time and stress and provide you with a newfound sense of independence, which always feels good after a successful job. In this article, we will outline a few basic scenarios which you can easily address yourself.

Squealing

If your vehicle emits a squealing sound every time you press your foot to the brake pedal, it is generally an indication of issues which require immediate attention. The common cause is worn out pads. These pads must be replaced as soon as possible in order to keep you and your vehicle safe from harm. The high pitched sound you hear is actually the grinding of brake mechanism parts.

However, if your squealing tends to be a bit more muted or occurred intermittently, it be simply be a sign that your pads are surrounded by dirt and dust. This problem can easily be addressed by taking your vehicle over to your local car wash and having it cleaned throughout. Other reasons include low quality liners or worn out backing plates. Inspect your liners and backing plates and replace if necessary.

Additionally, you may want to inspect the alignment. You can generally tell if improper alignment is the cause if the squealing persists after you’ve added fluid and replaced the pads.

Wear Brakes

If the response of your system is low even when the pedal is pushed to the floor, you may be looking at low fluid amounts. Low levels of fluid can cause your stopping power to diminish, so be sure to check your levels on a regular basis. Another possibility is that your pads are simply worn out. Worn out pads can greatly impact your braking performance and should be changed regularly.

Hard Pedal

Hard pedals are quite common in older cars and trucks. This is typically caused by vacuum system leaks. These leaks result in the loss of negative pressure, and thus, the driver will end up pressing down harder in order to obtain the desired reaction from the vehicle. Another possible answer is a break in the boost. Breaks and leaks within the booster will inhibit the fluid flow and work to prevent it from accessing various parts of the system. Inspect your system for breaks and leaks and replace any broken parts you happen to find.

Intermittent Actions

If you notice a loss in power every few seconds while pressing down on the pedal, the issue may lie within the discs and pads. Inspect the condition of both the discs and pads and replace them if needed.

If you’re still looking for the answers and have come to your wit’s end, the best possible solution is to make the trip over to your local brake repair mechanic. Having the eye of an experienced brake repair specialists at your side is always beneficial and will have you back on the road in no time.

Find a brake repair Quincy, IL specialist that can finally give you confidence in that your vehicle is fully efficient and safe on the road. For more information, visit http://www.meineke-quincyil.com/

Windows Repair – Do It Yourself

More than constructing a dream home, the real task begins when it comes to periodic maintenance. One of the important aspects in any building that adds an important aesthetic value to it is the Windows. Windows need periodic maintenance in terms of lubrication the joints as well as cleaning the glass and painting the frames. Due to constant exposure to heat and rain and other factors like dust, etc., Windows are vulnerable to repair or damage.

The glasses used in Windows are brittle by nature. So, a small scratch in the glass can get magnified to a crack and ultimately damage the complete glass frame. There are numerous simple ways to fix a scratched glass. But, you cannot expect the window to retain its original characteristics or appearance. There is every possibility of the glass having a rainbow effect on it. In some rare cases, a little application of pressure on the glass even as you to try to open or close the window might shatter the glass. Horrible thing to happen, huh?

Here is a very simple technique to make the scratch invisible on glass windows:

– First and foremost, safety first. So, ensure that you have your gloves on to avoid any injuries.

– Clean the glass thoroughly and wipe it dry with a cotton napkin.

– Apply either toothpaste or some cream along the area of the glass which has been scratched

– Scrape off the excess and when you do this, ensure that you do it unidirectional. To and fro scraping might only worsen the situation by aggravating the damage to the glass

– Once the paste or the cream has dried off, buff your cloth clean to have a glossy look.

If the scratch is not a very visible mark, try buffing your Kansas City Windows with a little furniture polish. Just be careful to avoid jagged materials – like newspaper – during cleaning. Your best bet is always a soft, dry cloth.

Prevention is better than cure!!

Here are few tips on how to avoid the scratches on the glass windows even before it can occur:

– Try to avoid paper or a rough cloth to clean the window

– The dust accumulated on the glass surface can be abrasive in nature too. So, rinse or hose the glass off before wiping it down

The above mentioned tips and solutions are only for minor scratches on your glass replacement windows Kansas City. These days, several kits are available in the market to remove scratches from windows. But watch out for the price tag. Sometimes, they can be quite expensive, and without the professional guidance, you may not be able to use them to your advantage.

The author of this article has an in depth on knowledge about the Kansas City Windows fixing and replacement windows Kansas City methods. He has also written articles on Material selection for windows, DIY for windows replacement Kansas City, etc.

DIY Xbox Repair

Once, in living memory, most technology was not particularly reliable and many items broke down on a fairly regular basis. Even relatively low tech Items like a pop up toaster used to have to get its elements either replaced or rewired every so often. Light bulbs were all incandescent and used to burn out every few 100 hours. (There were some places where on could buy light bulbs rated for a slightly higher voltage so the light was marginally dimmer but they used to burn for thousands of hours instead).

Within every town and suburb there was some little guy who owned a general repair shop. He would undertake repairs for all sorts of appliances, from Vacuum cleaners needing belts replaced or motors rewound, to refrigerators and washing machines.

Hi Fi equipment, TVs and Video recording units were likewise expensive to begin with and when they had a failure you had to find someone to repair it. These repair technicians were somewhat more specialised but nevertheless existed and serviced a niche in the market.

However over the last 20 years things have changed considerably. For a start electronics has improved hugely. Thus many electronically controlled items are designed and built to last. And last they do. Electronic components are usually soldered onto a printed circuit board and nothing is really serviceable.

The other point is that many appliances are now no longer particularly expensive. One no longer would even think about repairing a toaster or a kettle. Vacuum cleaners tend not to break but when they go faulty purchasing a new unit is no longer a budget breaking expense.

If the control unit of an appliance becomes faulty the chances are, if a repairman will undertake to even look at it, he will rip out and replace the circuit board without any attempt to trace its fault.

In the days when computer monitors were still cathode ray tubes the technician would explain that you could purchase a new one for little more than he would charge to even open a faulty one. Nowadays with electronic circuit boards and LCD and even LCD screens there definitely no service parts so if you have one go faulty on you, and it is out of your service warranty period there is almost nothing for it but to purchase a replacement.

Imagine therefore the chagrin of the Xbox 360 owner when failures started to occur soon after launch. Many of these faults were minor software errors which were corrected by upgrades but other became more serious.

The LED lights on the on/off switch normally glow green when everything is functioning as it should.

If one of these LEDs started showing red then an error has occurred. These were usually minor and could be reset by switching the unit off and on again. But one in particular got the name ‘The red ring of death’

The commonest cause is over-heating and it could be reset by switching off and letting it cool in a well ventilated place for an hour. If not, and it is out of guarantee there are Xbox repair instructions on line.

If your Xbox 360 has a red ring of death then DIY Xbox repair may help you repair it.

Clean Clean Clean Furnace Repair

We are a trustful company in Randolph MA specialized in furnace repair. This includes chimney cleaning, dryer vent cleaning, tuning-up and repairing furnaces and inspecting all this kind of systems by trying to find the best solution to your problem. We provide free chimney inspection, this meaning that we take our responsability in inspecting for carbon monoxide hazards. Our motto is Be there so not to be cold.

Our service is timeless

We provide on-time repairs, 24 hours per day, 7 days a week, installation and maintenance, for the best warranties, lowest costs and same as cash financing. The problems we are solving are these: furnace gas leak, pilot gas going out, furnace not heating enough, furnace not heating at all, furnace flame not igniting, furnace cycles on & off too often, blower motor runing but doesn’t blow air, blower not stopping, air handle squeals, furnace cabinet rattles, noisy air ducts.

We offer you the best solution in periodic furnace maintenance by giving the best prices and the best technical solutions. We are willing to provide a pleasant environment for you to live and feel warm. So that’s why our suggestion is that you should always keep in mind a preventive periodic maintenance so there won’t be a problem in the cold winter. Take advantage of the warm season and perform a quick check-up of your furnace system. You might be facing some technical surprises!

Experience, experts

Our company is willing to examine your entire furnace system. We have experienced technicians doing their jobs with passion and respect, trained to offer you the best solutions on every related issue you have.

Here are some of the important issues we are prepared to stand up for your help: peak performance of the operating furnace, efficiency of the energy of your furnace, easy-to-clean filters for having a special furnace.

With our company line and experience you can manage a very close confort with our line of furnices. There is no need to worry about warranties because we have it all resolved and all for you to save as much as you can from the repairings and to be satisfied with our workers and with the repaired furnace.

Special prices

Our company is in the working area for some years so we are familiar with all the marketing issues about billing. We are offering special furnace service and maintenance plans, depending on the kind of problem your are facing or on the kind of furnace you are willing to buy. Also, our billing and payment methods and terms are very well established from the beginning, depending on the difficulty of the reparation. All we can say is that we are willing to offer you the best and the lowest prices for any kind of repairing. Don’t hesitate to call us if you have a serious problem with your furnace. We are here to clean when you need it.

After A Long Search In Getting the best company which has highest reputation and best customer service to get your Furnace repair in Randolph area i found Green Energy Mechanical the best in town please visit there site Furnace repair Randolph ma.